Hydraulic Fluid Power Connection Winner 24° Cone Connectors/Adapters
Product Introduction
inner brand 24°cone connectors / adapters meet and exceed ISO 8434-1 requirements and performance. The pressure ratings are more higher than ISO 8434-1.
24° cone connectors using cutting ring and O-ring seal cone (referred to as DKO) suitable for use with ferrous and non-ferrous tubes with outside diameters from 4 mm to 42 mm inclusive. These connectors are for use in fluid power and general applications within the limits of pressure and temperature. They are intended for the connection of plain end tubes and hose fittings to ports in accordance with ISO 6149-1, ISO 1179-1 and ISO 9974-1.
Below figure show the cross sections and component parts of typical 24°cone connectors with cutting ring.
Key
1 body
2 nut
3 cutting ring
Below figure show the cross section of typical 24°cone connector with O-ring seal cone (DKO) end.
Key
1 body
2 nut
3 DKO-end (including O-ring)
24°cone connectors have L series for light duty and S series for heavy duty, detail maximum working pressure see below table.
|
No. |
Size |
Tube O.D. |
WP (MPa) |
|
L series |
|||
|
1 |
C-12 |
6 |
50 |
|
2 |
C-14 |
8 |
50 |
|
3 |
C-16 |
10 |
50 |
|
4 |
C-18 |
12 |
40 |
|
5 |
C-22 |
15 |
40 |
|
6 |
C-26 |
18 |
40 |
|
7 |
C-30 |
22 |
25 |
|
8 |
C-36 |
28 |
25 |
|
9 |
C-45 |
35 |
25 |
|
10 |
C-52 |
42 |
25 |
|
S series |
|||
|
1 |
D-14 |
6 |
80 |
|
2 |
D-16 |
8 |
80 |
|
3 |
D-18 |
10 |
80 |
|
4 |
D-20 |
12 |
63 |
|
5 |
D-22 |
14 |
63 |
|
6 |
D-24 |
16 |
63 |
|
7 |
D-30 |
20 |
42 |
|
8 |
D-36 |
25 |
42 |
|
9 |
D-42 |
30 |
42 |
|
10 |
D-52 |
38 |
25 |
When use 24° cone connectors with cutting ring, it is very important that as correct assembly instructions for no leakage. Best practice regarding reliability and safety is achieved by pre-assembling the cuttings using a suitable machines and along with tools and setup parameters.
Product Number
| Union |
 1C, 1D |
 1C-reduce, 1D-reduce |
 1C9, 1D9 |
 AC, AD |
||||
| Metric stud end |
 1CM-WD, 1DM-WD |
 1CH-N, 1DH-N |
 1CH4-OGN, 1DH4-OGN |
 1CH9-OGN, 1DH9-OGN |
 ACCH-OGN, ADDH-OGN |
 ACHC-OGN, ADHD-OGN |
||
| BSP stud end |
 1CB, 1DB |
 1CB-WD, 1DB-WD |
 1CG, 1DG |
 1CG4-OG, 1DG4-OG |
 1CG9-OG, 1DG9-OG |
|||
| UN sutd end |
 1CJ, 1DJ |
 1CO, 1DO |
 1CO4-OG, 1DO4-OG |
 1CO9-OG, 1DO9-OG |
 ACCO-OG, ADDO-OG |
 ACOC-OG, ADOD-OG |
||
| Banjo |
 1CI-WD, 1DI-WD |
 1CI-B-WD, 1DI-B-WD |
||||||
| Flange |
 1CFL, 1DFL |
 1CFL9, 1DFL9 |
 1DFS |
|||||
| Weld on |
 1CW, 1DW |
|||||||
| Taper thread end |
 1CN, 1DN |
 1CT-SP, 1DT-SP |
||||||
| Buckhead |
 6C, 6D |
 6C-LN, 6D-LN |
 8C-LN |
|||||
| Plug |
 4C, 4D |
 9C, 9D |
||||||
| Female swivel |
 2C, 2D |
 2C4, 2D4 |
 2C9, 2D9 |
 2BC-WD, 2BD-WD |
 2GC, 2GD |
 2HC-N, 2HD-N |
 BC, BD |
 CC, CD |
| Nut and cutting ring |
 NL, NS |
 RL, RS |